In color LCDs each individual pixel is divided into three cells, or subpixels, which are colored red, green, and blue, respectively, by additional filters (pigment filters, dye filters and metal oxide filters). Each subpixel can be controlled independently to yield thousands or millions of possible colors for each pixel. CRT monitors employ a similar 'subpixel' structures via phosphors, although the electron beam employed in CRTs do not hit exact 'subpixels'.
Color components may be arrayed in various pixel geometries, depending on the monitor's usage. If the software knows which type of geometry is being used in a given LCD, this can be used to increase the apparent resolution of the monitor through subpixel rendering. This technique is especially useful for text anti-aliasing.
To reduce smudging in a moving picture when pixels do not respond quickly enough to color changes, so-called pixel overdrive may be used.
[edit] Passive-matrix and active-matrix addressed LCDs
A general purpose alphanumeric LCD, with two lines of 16 characters.LCDs with a small number of segments, such as those used in digital watches and pocket calculators, have individual electrical contacts for each segment. An external dedicated circuit supplies an electric charge to control each segment. This display structure is unwieldy for more than a few display elements.
Small monochrome displays such as those found in personal organizers, or older laptop screens have a passive-matrix structure employing super-twisted nematic (STN) or double-layer STN (DSTN) technology—the latter of which addresses a color-shifting problem with the former—and color-STN (CSTN)—wherein color is added by using an internal filter. Each row or column of the display has a single electrical circuit. The pixels are addressed one at a time by row and column addresses. This type of display is called passive-matrix addressed because the pixel must retain its state between refreshes without the benefit of a steady electrical charge. As the number of pixels (and, correspondingly, columns and rows) increases, this type of display becomes less feasible. Very slow response times and poor contrast are typical of passive-matrix addressed LCDs.
High-resolution color displays such as modern LCD computer monitors and televisions use an active matrix structure. A matrix of thin-film transistors (TFTs) is added to the polarizing and color filters. Each pixel has its own dedicated transistor, allowing each column line to access one pixel. When a row line is activated, all of the column lines are connected to a row of pixels and the correct voltage is driven onto all of the column lines. The row line is then deactivated and the next row line is activated. All of the row lines are activated in sequence during a refresh operation. Active-matrix addressed displays look "brighter" and "sharper" than passive-matrix addressed displays of the same size, and generally have quicker response times, producing much better images.
[edit] Active matrix technologies
A Casio 1.8" color TFT liquid crystal display which equips the Sony Cyber-shot DSC-P93A digital compact camerasMain articles: Thin film transistor liquid crystal display and Active-matrix liquid crystal display
[edit] Twisted nematic (TN)
Twisted nematic displays contain liquid crystal elements which twist and untwist at varying degrees to allow light to pass through. When no voltage is applied to a TN liquid crystal cell, the light is polarized to pass through the cell. In proportion to the voltage applied, the LC cells twist up to 90 degrees changing the polarization and blocking the light's path. By properly adjusting the level of the voltage almost any grey level or transmission can be achieved.
For a more comprehensive description refer to the section on the twisted nematic field effect.
[edit] In-plane switching (IPS)
In-plane switching is an LCD technology which aligns the liquid crystal cells in a horizontal direction. In this method, the electrical field is applied through each end of the crystal, but this requires two transistors for each pixel instead of the single transistor needed for a standard thin-film transistor (TFT) display. This results in blocking more transmission area, thus requiring a brighter backlight, which will consume more power, making this type of display less desirable for notebook computers.
[edit] Advanced Fringe Field Switching (AFFS)
Advanced Fringe Field Switching is a similar technology to IPS or S-IPS offering superior performance and color gamut besides high luminosity. AFFS is developed by Boe Hydis Displays, Korea.
AFFS-applied notebook applications minimize color distortion while maintaining its superior wide viewing angle for a professional display. Color shift and deviation caused by light leakage is corrected by optimizing the white gamut which also enhances white/grey reproduction.
In premium IBM ThinkPad series notebooks, Boe Hydis AFFS displays are used to provide higher resolutions up to 1600x1200 in a relatively small 15 inch display setting. IBM also advertised these high end panels under their FlexViewTM label. AFFS panels are mostly classified under the VIEWIZTM name by Boe Hydis resembling premium performance.
As of 2008, Hitachi acquired AFFS license to manufacture high end panels in their product line. Boe Hydis suspended their production of high quality displays however the company still advertises the benefits of the superior technology.
[edit] Vertical alignment (VA)
Vertical alignment displays are a form of LC displays in which the liquid crystal material naturally exists in a horizontal state removing the need for extra transistors (as in IPS). When no voltage is applied the liquid crystal cell, it remains perpendicular to the substrate creating a black display. When voltage is applied, the liquid crystal cells shift to a horizontal position, parallel to the substrate, allowing light to pass through and create a white display. VA liquid crystal displays provide some of the same advantages as IPS panels, particularly an improved viewing angle and improved black level.
[edit] Blue Phase mode
Main article: Blue Phase Mode LCD
Blue phase LCDs do not require an LC top layer. Blue phase LCDs are relatively new to the market,and very expensive because of the low volume of production. They provide a higher refresh rate than normal LCDs, but normal LCDs are still cheaper to make and actually provide better colors and a sharper image.[citation needed] .
[edit] Quality control
Some LCD panels have defective transistors, causing permanently lit or unlit pixels which are commonly referred to as stuck pixels or dead pixels respectively. Unlike integrated circuits (ICs), LCD panels with a few defective pixels are usually still usable. It is also economically prohibitive to discard a panel with just a few defective pixels because LCD panels are much larger than ICs. Manufacturers have different standards for determining a maximum acceptable number of defective pixels. The maximum acceptable number of defective pixels for LCD varies greatly. At one point, Samsung held a zero-tolerance policy for LCD monitors sold in Korea.[18] Currently, though, Samsung adheres to the less restrictive ISO 13406-2 standard.[19] Other companies have been known to tolerate as many as 11 dead pixels in their policies.[20] Dead pixel policies are often hotly debated between manufacturers and customers. To regulate the acceptability of defects and to protect the end user, ISO released the ISO 13406-2 standard.[21] However, not every LCD manufacturer conforms to the ISO standard and the ISO standard is quite often interpreted in different ways.
Examples of defects in LCDsLCD panels are more likely to have defects than most ICs due to their larger size. In the example to the right, a 300 mm SVGA LCD has 8 defects and a 150 mm wafer has only 3 defects. However, 134 of the 137 dies on the wafer will be acceptable, whereas rejection of the LCD panel would be a 0% yield. The standard is much higher now due to fierce competition between manufacturers and improved quality control. An SVGA LCD panel with 4 defective pixels is usually considered defective and customers can request an exchange for a new one. Some manufacturers, notably in South Korea where some of the largest LCD panel manufacturers, such as LG, are located, now have "zero defective pixel guarantee", which is an extra screening process which can then determine "A" and "B" grade panels. Many manufacturers would replace a product even with one defective pixel. Even where such guarantees do not exist, the location of defective pixels is important. A display with only a few defective pixels may be unacceptable if the defective pixels are near each other. Manufacturers may also relax their replacement criteria when defective pixels are in the center of the viewing area.
LCD panels also have defects known as mura, which look like a small-scale crack with very small changes in luminance or color.[22] It is most visible in dark or black areas of displayed scenes. Defects in various LCD panel components can cause mura effect.[clarification needed]
[edit] Zero-power (bistable) displays
The zenithal bistable device (ZBD), developed by QinetiQ (formerly DERA), can retain an image without power. The crystals may exist in one of two stable orientations (Black and "White") and power is only required to change the image. ZBD Displays is a spin-off company from QinetiQ who manufacture both grayscale and color ZBD devices.
A French company, Nemoptic, has developed another zero-power, paper-like LCD technology which has been mass-produced since July 2003. This technology is intended for use in applications such as Electronic Shelf Labels, E-books, E-documents, E-newspapers, E-dictionaries, Industrial sensors, Ultra-Mobile PCs, etc. Zero-power LCDs are a category of electronic paper.
Kent Displays has also developed a "no power" display that uses Polymer Stabilized Cholesteric Liquid Crystals (ChLCD). The major drawback to the ChLCD is slow refresh rate, especially with low temperatures.
In 2004 researchers at the University of Oxford demonstrated two new types of zero-power bistable LCDs based on Zenithal bistable techniques.[23]
Several bistable technologies, like the 360° BTN and the bistable cholesteric, depend mainly on the bulk properties of the liquid crystal (LC) and use standard strong anchoring, with alignment films and LC mixtures similar to the traditional monostable materials. Other bistable technologies (i.e. Binem Technology) are based mainly on the surface properties and need specific weak anchoring materials.
See Ferro Liquid Display for more information about ferro fluid based bistable displays.
No comments:
Post a Comment